• Quantity:
Discount:
Shipping:
Payment:
Taxes:
Total: {price to quote}
Cart is empty.

Login

 
or
Login with PayPal
Cannot login with PayPal
Cannot login with Facebook

Top Sellers

  1. 1
    Veneziani Timber Gloss Paint 0,75 Lt #473COL195
    Price:
    €18.75
    Listing:
    €22.06
    You Save:
    - 15%
  2. 2
    Stoppani Clipper One Component Enamel 0,75 Lt Forest Green 30319 #466COL9017
    Price:
    €24.19
    Listing:
    €32.26
    You Save:
    - 25%
  3. 3
    Veneziani Thinner 6470 0,5 Lt #473COL253
    Price:
    €7.30
    Listing:
    €8.58
    You Save:
    - 15%
  4. 4
    International VC 17m Extra  Antifouling 2 Lt Graphite YBA762 #458COL313
    Price:
    €144.90
    Listing:
    €275.72
    You Save:
    - 47%
  5. 5
    Veneziani Eurosprint NEXT Antifouling Blu-Blue-Bleu 0,75 Lt #473COL264
    Price:
    €35.52
    Listing:
    €47.40
    You Save:
    - 25%

International Interdeck Anti-slip Enamel 0,75 Lt White YJB000 #458COL687

International Interdeck Anti-slip Enamel 0,75 Lt White YJB000 #458COL687

Interdeck provides an excellent non-slip finish. It contains a fine aggregate and is easy to apply on all surfaces. The low sheen finish prevents bright reflections off the decks.

Listing:
€38.06
Price:
€28.55
You Save:
€9.52 (25%)
Combination not available

PRODUCT DESCRIPTION

Interdeck provides an excellent slip resistant finish. It contains a fine aggregate and will apply easily on all substrates.

* Low sheen finish prevents bright reflections off the decks
* Easy application
* Available in a range of colours
The tough polyurethane resin protects decks against everyday wear and tear.

PRODUCT INFORMATION
Colour: YJB000-White, YJB923-Squall Blue, YJC089-Cream, YJF684-Grey, YJG009-Sand Beige
Finish: Low sheen
Specific Gravity 1.4
Volume Solids 54%
Typical Shelf Life: 2 yrs
VOC (As Supplied) 357 g/lt
Unit Size: 750 ml

DRYING/OVERCOATING INFORMATION
Drying
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F)
Touch Dry 5 hrs 4 hrs 3 hrs 2 hrs
Dry To Walk On 4 days 3 days 2 days 1 days
Overcoating
Substrate Temperature
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Interdeck 24 hrs 4 days 20 hrs 3 days 16 hrs 2 days 12 hrs 1 days

APPLICATION AND USE
Preparation: PREVIOUSLY PAINTED SURFACES
In Good Condition: Wash with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 280-320grade (grit) paper.
In Poor Condition: Remove all previous coatings and prime the substrate.

PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE/NATURAL WOOD: Sand smooth with 80-180 grit paper and then 280 grit paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems).

STEEL: Degrease with solvent or suitable detergent cleaner. Gritblast to Sa 2½ - near white metal surface. If gritblasting is not possible, grind the metal surface with 24-36 grit abrasive discs to a uniform, clean, bright metal surface with a 50-75 microns anchor pattern. Use angle grinder on small areas. Clean thoroughly and allow to dry. Pre-prime using an International primer as detailed for specific coating systems.

ALUMINIUM: Degrease with solvent or suitable detergent cleaner. Sand well using 24-120 grit (aluminium compatible) paper. Coarser grades are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Pre-prime using an International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

GRP: Degrease with solvent or suitable detergent cleaner. Sand well using 60-120 grit paper. Clean thoroughly and allow to dry. Pre-prime using an International primer as detailed for specific coating systems.

AGED/WEATHERED GELCOATS: Due to the potentially porous nature of aged/weathered gelcoats the risk of solvent/moisture entrapment after painting is much higher than when gelcoat is new. As a result this entrapment could lead to blistering of the paint film. To reduce the risk of paint film blistering it is recommended that 3 coats of Interprotect are applied to seal the gelcoat. Interprotect must be overcoated with Perfection Undercoat prior to topcoat application.

ALL SUBSTRATES: If any filling is required use the appropriate product from the International range.
Method: Sand the primer with 180-220 grit wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats.

Useful Tips: Mixing: Stir well before use.
Thinner: YTA800 Thinners No.1
Cleaner: YTA800 Thinners No.1 Ventilation and Humidity Control Apply in dry, well ventilated conditions.

Other: For best results either stipple by brush or use a mohair roller.

Some Important Points: Formulated for exterior use.
Product temperature should be minimum 10°C/50°F and maximum 30°C/86°F.
Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F.
Substrate temperature should be minimum 5°C/41°F and maximum 35°C/95°F.

Compatibility/Substrates: Suitable for all substrates and filled surfaces. Not suitable for permanently immersed surfaces. Do not clean with highly alkaline cleaners.
Number of Coats: 1-2
Coverage/spreading rate (Theoretical) - 10.8 m²/lt
Recommended dry film thickness (DFT) per coat 50 microns
Recommended wet film thickness (WFT) per coat 93 microns
Application: Methods Brush, Roller.
Not suitable for spray application.

TRANSPORTATION, STORAGE AND SAFETY INFORMATION
Storage: GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For full shelf life of Interdeck, ensure that the container is firmly closed between uses and the temperature is between 5°C/41°F and 35°C/95°F. Keep out of direct sunlight.

TRANSPORTATION:
Interdeck should be kept in securely closed containers during transport and storage.

Safety GENERAL:
Read the label safety section for Health and Safety Information.

DISPOSAL:
Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.
Remainders of Interdeck cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for with local authorities.

IMPORTANT NOTES: The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further enquiries as to the suitability of the product for the intended purpose does so at his own risk.

  1. 1
    International Thinner No.1 1 Lt #458COL6500
    Thinner No.1 is suitable for thinning and / or equipment cleaning in association with: pack paints and varnishes - Yacht Primer, Toplac®, Pre-Kote, Interdeck®, Danboline, Original, Goldspar®, Goldspar Satin, Schooner®.
    Price:
    €14.55
    Listing:
    €19.40
    You Save:
    - 25%