• Quantity:
Discount:
Shipping:
Payment:
Taxes:
Total: {price to quote}
Cart is empty.

Login

 
or
Login with PayPal
Cannot login with PayPal
Cannot login with Facebook

Top Sellers

  1. 1
    International Perfection Plus Varnish 0,75 Lt Transparent YVA950 #458COL685
    Price:
    €43.03
    Listing:
    €57.36
    You Save:
    - 25%
  2. 2
    Rotaschaum extra fine paint Roller  L. 11 cm D. 35 mm H. 6 mm #478COL1065
    Price:
    €1.30
    Listing:
    €1.53
    You Save:
    - 15%
  3. 3
    Boero Thinner 703 0,5 Lt Thinner for one-component products #45100705
    Price:
    €3.40
    Listing:
    €5.67
    You Save:
    - 40%
  4. 4
    Veneziani Thinner 6470 0,5 Lt #473COL253
    Price:
    €7.30
    Listing:
    €8.58
    You Save:
    - 15%
  5. 5
    Teak Wonder Brightner Lt 4 #467COL509
    Price:
    €25.62
    Listing:
    €34.16
    You Save:
    - 25%

International Watertite Epoxy Filler 1 Lt #458COL671

International Watertite Epoxy Filler 1 Lt #458COL671

Watertite Epoxy Filler is a filler producing a highly polished finish. It can be applied both on hull and topsides. The very waterproof formula makes it suitable for application in osmosis treatment cycles.

Listing:
€89.06
Price:
€66.80
You Save:
€22.27 (25%)
Combination not available

PRODUCT DESCRIPTION

Watertite Epoxy Filler is a filler producing a highly polished finish. It can be applied both on hull and topsides. The very waterproof formula makes it suitable for application in osmosis treatment cycles.

* Fills up to 20 mm without sagging
* Use above and below the waterline
* High strength and adhesion properties
* Simple 1:1 mixing ratio for easy measurement of components
* Very fast drying
* Super-smooth

PRODUCT INFORMATION
Colour: YAV145/A - Light Blue
Base product code is YAV335 & curing agent product code is YAA441.
Specific Gravity 1.02
Volume Solids 100%
Mixing Ratio 1:1 by volume (as supplied)
Converter/Curing Agent YAA441
Typical Shelf Life: 2 yrs
VOC (As Supplied) 0 g/lt
Unit Size: 250 ml, 1 lt

DRYING/OVERCOATING INFORMATION
Drying
10°C (50°F)  15°C (59°F)  23°C (73°F)  35°C (95°F)
Sandable 10 hrs 6 hrs 5 hrs 4 hrs
Immersion 5 days 3 days 2 days 36 hrs
Pot Life 25 mins 20 mins 15 mins 10 mins

Note: At 7°C the pot life is 30 mins and the product is sandable after 24 hrs, immersion after 6 days.

Overcoating
Substrate Temperature
10°C (50°F)  15°C (59°F)  23°C (73°F)  35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Gelshield 200 10 hrs - 6 hrs - 5 hrs - 4 hrs -
Interprotect 10 hrs - 6 hrs - 5 hrs - 4 hrs -
Perfection Undercoat 10 hrs - 6 hrs - 5 hrs - 4 hrs -
Primocon 10 hrs - 6 hrs - 5 hrs - 4 hrs -
VC Tar2 10 hrs - 6 hrs - 5 hrs - 4 hrs -
Watertite 10 hrs - 6 hrs - 5 hrs - 4 hrs -
Yacht Primer 10 hrs - 6 hrs - 5 hrs - 4 hrs -
Yacht Primer (Professional) 10 hrs - 6 hrs - 5 hrs - 4 hrs -

APPLICATION AND USE
Preparation: The surface must be clean and dry. When treating osmosis, prime with Gelshield first. Otherwise prime as below.

BARE/NATURAL GRP: Gelshield 200 or VC Tar 2 for osmosis protection, or Primocon.

STEEL/IRON :Above water: Interprotect or Yacht Primer. Below water: Interprotect, or VC Tar 2, or Primocon.

ALUMINIUM: Above water: Interprotect or Yacht Primer. Below water: Interprotect, or VC Tar 2, or Primocon.

LEAD: VC Tar 2, or Interprotect or Primocon.

BARE/NATURAL WOOD: Above water: Yacht primer. Below water: Interprotect or Primocon.

Method: Remove any dust from the surface. Apply firmly in a spreading action. Fill to a level slightly above the surrounding area.
When hardened, sand smooth with 80-220 grade wet or dry paper. If left longer than 24 hours, two component epoxy fillers will need sanding with 80-220 grade wet or dry paper to ensure a good physical key.

Useful Tips: Mixing: Mix the two components thoroughly to an even colour. Mix both components together thoroughly to correct mix ratio.

Thinning: Do not thin. Cleaner YTA061 Thinners No.7
Ventilation and Humidity Control: Avoid cold, damp conditions which may cause a stickiness to form on the surface.
This should be removed by water and a 3M Scotchbrite pad or sanding.

Other: Large areas should be sanded with paper on a board twice the length of the repair area, this will allow for curvature of the hull. Small areas can be sanded using a sanding block. Sand as soon as possible after the sandable time as Watertite continues to harden with time.

Some Important Points: Do not use below 7°C. Do not apply more than 2.0 cm thickness at any one time. Product temperature should be minimum 10°C and maximum 35°C. Ambient temperature should be minimum 7°C and maximum 35°C. Substrate temperature should be minimum 7°C/45°F and maximum 35°C/95°F.

Compatibility/Substrates: Will not adhere well to undercured GRP laminate. Allow to fully cure before abrading laminate and applying Watertite.
Number of Coats As required
Coverage/spreading rate: (Theoretical) - 0.2 m²/lt @ 5000 microns WFT. Variable depending on thickness.
Application Methods: Palette knife or spreader

TRANSPORTATION,STORAGE AND SAFETY INFORMATION
Storage: GENERAL INFORMATION:

Exposure to air and extremes of temperature should be avoided. For full shelf life of Watertite, ensure that the container is firmly closed between uses and the temperature is between 5°C/41°F and 35°C/95°F. Keep out of direct sunlight.

TRANSPORTATION:
Watertite should be kept in securely closed containers during transport and storage.

Safety GENERAL:
Read the label safety section for Health and Safety Information.

DISPOSAL:
Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden beforedisposal.
Remainders of Watertite cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for with local authorities.

IMPORTANT NOTES: The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further enquiries as to the suitability of the product for the intended purpose does so at his own risk.