• Quantity:
Discount:
Shipping:
Payment:
Taxes:
Total: {price to quote}
Cart is empty.

Login

 
or
Login with PayPal
Cannot login with PayPal
Cannot login with Facebook

Top Sellers

  1. 1
    Veneziani Timber Gloss Paint 0,75 Lt #473COL195
    Price:
    €18.75
    Listing:
    €22.06
    You Save:
    - 15%
  2. 2
    Stoppani Clipper One Component Enamel 0,75 Lt Forest Green 30319 #466COL9017
    Price:
    €24.19
    Listing:
    €32.26
    You Save:
    - 25%
  3. 3
    Veneziani Thinner 6470 0,5 Lt #473COL253
    Price:
    €7.30
    Listing:
    €8.58
    You Save:
    - 15%
  4. 4
    International VC 17m Extra  Antifouling 2 Lt Graphite YBA762 #458COL313
    Price:
    €144.90
    Listing:
    €275.72
    You Save:
    - 47%
  5. 5
    Veneziani Eurosprint NEXT Antifouling Blu-Blue-Bleu 0,75 Lt #473COL264
    Price:
    €35.52
    Listing:
    €47.40
    You Save:
    - 25%

Hempel High Protect 0,75 Lt Grey #456COL032

Hempel High Protect 0,75 Lt Grey #456COL032

HEMPEL HIGH PROTECT is a high build two-component solvent-free epoxy primer. It forms a hard, tough and water-resistant coating. As a primer below the waterline of fiberglass boats and steel.

Listing:
€53.07
Price:
€39.81
You Save:
€13.26 (25%)
Combination not available

MORE INFORMATION

HIGH PROTECT A + B PRIMER

PHYSICAL CONSTANTS:

Finish: High gloss
Volume solids,% 100
Theoretical coverage: 2.9 m2 / l [116.3 sq.ft. / US gallon] - 350 micron / 14 mils
Flash point: 74 ° C [165.2 ° F]
Specific weight: 1.3 kg / liter [10.5 lb / US gallons]
Touch dry: 10-12 hour (s) 20 ° C / 68 ° F, 22 to 27 hours at 10 ° C / 50 ° F
Fully cured: 7 days (i) 20 ° C / 68 ° F, 14 days (i) at 10 ° C / 50 ° F
VOC content: 10 g / l [0.1 lb / US gallons]

APPLICATION DETAILS:

Mixing ratio: 3: 2 by volume
Application method: Airless / brush / sponge roller
Thinner, (volume max): Do not dilute
Pot life: 45 minutes (i) 20 ° C / 68 ° F, 60 minutes at 15 ° C / 59 ° F
Nozzle diameter: 0.023 "
Nozzle pressure: 250 bar [3625 psi] (Airless spray data are indicative and subject to adjustment)
Cleaning equipment: HEMPEL'S THINNER 08451 The roller is discarded after use.
Indicated dry film thickness  350 micron [14 mils]
Indicated wet film thickness 350 micron [14 mils]
Recoating interval, min as per specification.
Recoating interval, max as per specification.

SURFACE PREPARATION:

Wash the area to be treated with HEMPEL'S PRE-CLEAN 67602 as shown in the instructions and rinse with fresh water. Remove salt and other contaminants by cleaning with fresh water at high pressure. Fiberglass: The surface should be roughened to an even roughness (sandpaper, grit 80-100). Remove the dust. Steel: Sanding degree Sa 2½, ISO 8501-1: 2007, roughness parameters corresponding to Rugotest No. 3, BN 11.

CONDITIONS OF APPLICATION:

Use only when the application and curing take place at temperatures higher than 10°C / 50°F. The temperature of the paint must be equal to 15°C or higher. When applying, the surface must be perfectly clean, dry and temperature must be above dew point to prevent the formation of condensa. Fiberglass: For repairs of osmosis, apply at least 2 layers with dry film thickness of 350 microns each (at least 4 layers with dry film thickness of 150 microns each for roller applications). For preventive treatments, apply at least one coat with a dry film thickness of 350 microns each (at least 2 layers with dry film thickness of 150 microns each for roller applications). Steel: minimum 3 layers of each 150 micron / 6 mils dry film thickness.

Application equipment

We recommend using ½'' hoses between the pump and the spray gun to avoid drop in pressure and, if possible, remove the suction hose.

Film thickness / dilution

It may be specified in a different thickness, depending on the mode and area of ​​use. This will alter the spreading rate. For application by roller, it is essential to ensure that the layer of the specified film is not poorous.

Catalyst

The catalyst is highly thixotropic. Add 3 basic parts to 2 parts of catalyst during the mixing.

Undocking

Do not place the boat in water before one-week catalysis of the last layer of the product (20 ° C). 2 weeks at 10 ° C / 50 ° F

Overcoating

If the interval indicated is exceeded, it will be necessary to apply a thin coat of HEMPEL'S LIGHT PRIMER 45551. After prolonged exposure to the elements, before recoating completely clean the surface using high-pressure cleaning with fresh water and let dry.

  1. 1
    Hempel Thinner 845 0,75 Lt #456COL036
    Thinner for epoxy products.
    Price:
    €10.98
    Listing:
    €14.64
    You Save:
    - 25%