• Quantity:
Total: {price to quote}
Cart is empty.


Login with PayPal
Cannot login with PayPal
Cannot login with Facebook

Top Sellers

  1. 1
    Rotaschaum  extra fine paint Roller L.11cm D.35mm H.6mm #478COL1066
    You Save:
    - 15%
  2. 2
    Veneziani Raffaello White Racing Antifouling  0,75 Lt #473COL379
    You Save:
    - 25%
  3. 3
    Marlin Velox Plus Antifouling 0,5 Lt Sweden Grey  #461COL517
    You Save:
    - 38%
  4. 5
    Nautical AkzoNobel Gloss Enamel 0,75 Lt Blue Middle #470COL2206
    You Save:
    - 7%

Attiva Marine Primer 0,75 Lt #451COL399

Attiva Marine Primer 0,75 Lt #451COL399

CUSTOM PRODUCT. Two-component universal insulating anti corrosive epoxy primer for every media type. Can also be used as intermediate undercoat.

You Save:
€4.78 (15%)
Combination not available


DESCRIPTION: universal primer or thick protection base
Color: white, gray 030 035
Type: two-component epoxy polyamide
Recommended use: On wood. For protection (marine weather and ultraviolet light) and decoration. For interior/exterior
POT LIFE: 6:00
Specific gravity: 1.30 ± 0.02 Kg/Lt (white)
SOLIDS by VOLUME: 45% ± 2%
COVERAGE PER COAT: (50 MICRONS dry): Theoretical 9 m²/lt - Practical: 7.8-m²/lt 7.2 (loss Factor: 13%-20%)
THICKNESS PER COAT: 100 Μm wet film thickness: dry film thickness: 50 microns
RECOATING TIME: minimum: maximum: 4:00 pm 48 h. (weather conditions)
LAUNCH TIME: minimum: Maximum 7 days: see drying table
Application method: brush-roller-spray (air or airless)
AIR APPLICATION: SPRAY nozzle diameter: 1.4-1.6 mm pressure: 2-4. Diluiz Kg/cm%: 10-15
AIRLESS APPLICATION: nozzle diameter: 0.015-0.018 mm output pressure: 150 Kg/cm
APPLICATION CONDITIONS: 5°-35° c. (15°-25° c. spray)-max humidity: 85%, no wind, dust, rain
Thinner: 128. For brush, roller 5% max. Preferably only on first coat
TEMP. Flash point: 24° C

NOTE: all times are calculated at a temperature of 20° C and then change with the change of temperature according to this rule: for every variation of about 10° C, times are doubled or halved.


Preparation (new or old media made new)

FIBERGLASS: Total and meticulous degreasing with anti silicone cleaner. Remove all the wax. An easy control system is to wet the hull and check the persistence of water droplets or streaks of oil through the sunrays. In that case repeat the degreasing otherwise there will be no adherence. Wash with fresh water only. Light sanding.

Wood: wipe any grease, resin, glue. Heavy sanding. Dry well. Immediately proceed immediately with soaking only the new wood impregnation with at least 2 coats of "Lignoguard".

STAINLESS STEEL/IRON: SA 2.5 sandblasting or ST 3 disking  (with large disks). The metal should be primed as soon as possible after surface preparation treatment and before the media shows signs of oxidation.

LIGHT ALLOYW: Thoroughly degrease, soft water wash, strong sanding or disking (for disks). If you sand, then use low pressure so as not to damage the metal and use fine-grained non-metallic abrasive. Apply a coat of primer before the media shows signs of oxidation and within 24 hours from the surface cleansing treatment.


FIBERGLASS: 1 coat (50 microns) protective Marine primer Primer (2-component). If osmosis prevention is desired then an additional 2-3 coats are required (150 microns) on hull and bilge.

STAINLESS STEEL/WOOD: 1 coat (50 microns) of Marine Primer plus 4 coats (200 microns) protective Marine Primer (two-component epoxy)

LIGHT ALLOY: 1 coat (50 microns) of Marine Primer plus 4 coats (200 microns) protective Marine Primer (two-component epoxy)

Warning: If a filler is required use only two-component epoxy type and apply it after the first coat of Marine Primer overcoating it with subsequent coats


Hull: Apply 2 full coats of antifouling.

Outboard: Apply 2 full coats of polyurethane enamel (Viva)


Marine Primer is long-lasting if 200 microns are applied (minimum 5 years). Does not require special maintenance. If over time it needs retouching, first remove the antifouling or paint and after a thorough sanding apply a further coat. Sanding may be substituted by Fiberguard anchoring primer only if antifoulng is applied as a subsequent coat.


Compatibility: "Marine Primer" is compatible with all 2k epoxy and polyurethane products and even with all antifouling paints. Can be coated with one-component "Fiberguard" primer.

ATTENTION: stir base and catalyst separately and then together before and during application • meticulously observe the overcoating times (at 20° C min. 16-max 48 h,  if the 48 hours are exceeded then heavily sand before the next coat. If the subsequent coat is an antifouling, sanding can be replaced with 1 coat of primer (Fiberguard) • protection is given only by applying the required thickness and this is achieved by applying the right amount (divide the surface to be coated (m2) by the practial coverage (m2/lt) and multiply the result by the number of coats required • since the times indicated in the datasheet vary with the temperature, to reduce errors apply 1 coat  per day, launch days after 7, and apply the catalyzed product within 2 hours •  Apply longitudinally and across  • Not suitable for flexible wood.